Skip to the content
Menu

Guide · Briquettes

How the coconut shisha briquettes are made

The factory in Tempuran, Kabupaten Magelang, Central Java, Indonesia makes its shisha briquettes in five steps, with a check at each. The steps, the machines and the share of binder are those the factory declares.

Published by
PT Nargile Coconut Charcoal Indonesia
Published
Updated
Pressed briquettes are dried in ovens until their moisture falls to the level set for packing.

In short

How are these shisha briquettes made, from shell charcoal to the packed box?

The factory presses and dries; it does not carbonize shell itself. Shell charcoal bought from Sulawesi is checked on arrival, bound with tapioca, pressed to size, dried for 48 hours or more in five electric ovens to 2% moisture at most, then checked piece by piece at packing. Output is 7 t of shisha briquettes a day, six days a week.

1. A pressing and drying plant

The factory presses and dries shisha charcoal; it does not carbonize shell itself. Its raw material is coconut shell charcoal bought from Sulawesi; the factory does not carbonize shell itself.

  1. Shell charcoal in

    The raw material arrives as coconut shell charcoal bought from Sulawesi; the factory does not carbonize shell itself. It is checked on arrival; then hammer mills grind it and a rotary sieve cleans it.

  2. Binding and pressing

    The charcoal is bound with tapioca, usually 1.5–3% of the mix, and extruded through laser-cut molds in the shape and size of the order.

  3. Drying

    Five electric ovens dry each batch for 48 hours or more.

  4. Testing

    Pieces are taken for the burn test and the drop test.

  5. Packing

    Each piece is inspected by hand as it is packed.

Who runs the factory, and where it is, is on the company.

2. The shell charcoal that comes in

The shell charcoal comes in bought from Sulawesi. Before it is used, each arrival is checked against the factory's limits for the raw material.

The checks on arrival: moisture under 12%, at least 82% fixed carbon, at most 14% volatile matter, the ash content and the color of the ash. The moisture content on arrival is the raw material's, not the finished piece's.

Each of these limits is set against the others on the limits.

3. Binding and pressing

Definition

binder

A binder is the substance mixed into ground charcoal that holds a pressed briquette together once it has dried.

Before binding, hammer mills grind the shell charcoal and a rotary sieve cleans it. The binder is tapioca, usually 1.5–3% of the mix.

The bound charcoal is extruded through laser-cut molds, in one of the six standard sizes or in a shape on request when an order asks for one; the other shapes are on shapes made on request.

The size is checked during pressing: four times a day, 20 pieces go under a digital caliper and each reading is logged. Every standard size is held to ±0.3 mm per side, its size tolerance.

A press forms the mixed charcoal and binder into pieces of one shape and size before drying.

4. Drying

Five electric ovens dry the pressed pieces. The setting: 48 hours or more per batch; moisture measured with a meter on every oven load; 2% at most.

The 2% at most limit is for the finished pieces, and it is lower than the limit for the shell charcoal on arrival. Each oven load is read with a meter.

A moisture meter reads the water left in a dried piece before the load is released for packing.

How the pieces are kept dry from the oven to the box and the container is on from the oven to the box.

5. Testing and packing

Pieces of a batch are tested before packing, and the last check is made by hand at the packing table.

  • The burn test: three pieces go on an electric coil; the time each takes to light and how long it burns are logged.
  • The drop test: a lit piece is dropped on a hard tiled floor, from 30 cm for hexagonal, dome and finger shapes and from 100 cm for cube and flat shapes; it passes if it stays whole after three drops.
  • The packing check: each piece is inspected by hand as it is packed.
  • The retained sample: about 25 kg of every batch for 5 years, sealed in bags marked with the batch number and date.

What each check looks for, and what fails a batch, is on the check after each step.

6. How much is made, and when

Output is 7 t a day, six days a week. Produced to order; no stock.

Note

Because nothing is pressed for stock, the production time of an order starts with the order; the steps of an order, from the deposit to on board, are on how an order runs.

Questions buyers ask

Does the factory make the charcoal from coconut shells itself?
No. The factory presses and dries; its raw material is coconut shell charcoal bought from Sulawesi; the factory does not carbonize shell itself.
What holds the briquettes together?
The binder is tapioca, usually 1.5–3% of the mix.

Ask for a quote for this size

The quote form asks about the piece, the pack, the load, the papers and the port, in that order.

Request a quote