Skip to the content
Menu

Guide · Briquettes

Testing a sample: burn, drop and size

These are the checks the factory runs on its shisha briquettes, written so that an importer of hookah charcoal can repeat them. A result taken this way can be set against the factory's own records.

Published by
PT Nargile Coconut Charcoal Indonesia
Published
Updated
An electric coil lights charcoal pieces evenly, so the time to light can be compared between samples.

In short

How can I test a sample of shisha briquettes the way the factory tests a batch?

Three of the factory's checks can be repeated on a sample: a burn test on an electric coil, a drop test and a caliper check. A batch fails on smell or smoke as the pieces warm up, high ash, cracked or broken pieces or pieces of uneven size or density, and the same signs can be looked for in a sample.

1. The factory's checks, in production order

Six checks run in the order of production, from the shell charcoal that arrives to the box that is closed. Three of them can be repeated on a sample.

  1. Incoming shell charcoal

    Each delivery is checked for moisture under 12%, at least 82% fixed carbon, at most 14% volatile matter, the ash content, the color of the ash.

  2. Size

    Four times a day, 20 pieces go under a digital caliper and each reading is logged.

  3. Drying

    48 hours or more per batch; moisture measured with a meter on every oven load; 2% at most.

  4. Burn

    Three pieces go on an electric coil; the time each takes to light and how long it burns are logged.

  5. Drop

    A lit piece is dropped on a hard tiled floor, from 30 cm for hexagonal, dome and finger shapes and from 100 cm for cube and flat shapes; it passes if it stays whole after three drops.

  6. Packing

    Each piece is inspected by hand as it is packed.

2. The burn test

Definition

burn test

A burn test lights a few pieces and records how long they take to light and how long they burn.

The factory's setting: three pieces go on an electric coil; the time each takes to light and how long it burns are logged. The same test needs only an electric coil and a timer.

  1. Take three pieces

    Take three pieces of one size and grade from the sample; test each size and grade the same way.

  2. Light them on a coil

    Place the three pieces on an electric coil and start a timer when the coil is switched on.

  3. Record the time to light

    Note when each piece is lit across its face.

  4. Record the burn time

    Note when each piece has burned down, and look at the ash it leaves.

Note

On the coil the factory has declared no target time. Its minutes come from timing a piece on a shisha bowl in use, until the smoking ends, and they are given for each size on the sizes compared. The time depends on the size of the piece, not its grade, so compare pieces of one size.

3. The drop test

Definition

drop test

A drop test lets lit pieces fall onto a hard floor from a set height and counts the drops each piece survives.

The factory's setting: a lit piece is dropped on a hard tiled floor, from 30 cm for hexagonal, dome and finger shapes and from 100 cm for cube and flat shapes; it passes if it stays whole after three drops. The height depends on the shape.

The drop height for each shape, as declared by the factory, onto a hard tiled floor.
ShapeDrop height
Cubes 100 cm
Hexagonal, dome and finger shapes 30 cm
Flat 100 cm

The longer hexagonal shisha briquette is dropped from the lower height. Use a hard tiled floor, and drop each lit piece three times.

A fixed height and a hard floor make a drop test repeatable from one batch to the next.

4. The size check

The size is held to ±0.3 mm per side, the size tolerance of every standard size. The factory's check: four times a day, 20 pieces go under a digital caliper and each reading is logged.

Measure 20 pieces of the sample with a digital caliper and set each reading against the nominal size. Then weigh a kilogram and count the pieces: the declared pieces per kilogram of each size are on pieces per kg of each size.

5. What fails a batch

Four signs fail a batch at the factory, and each can be looked for in a sample.

  • Smell or smoke as the pieces warm up
  • High ash
  • Cracked or broken pieces
  • Pieces of uneven size or density

High ash is judged against the grade: the ash content of each grade is on ash by grade.

6. The retained sample

Definition

retained sample

A retained sample is a quantity kept back from a production batch, sealed and labeled, against which later questions about the batch are checked.

The factory keeps about 25 kg of every batch for 5 years, sealed in bags marked with the batch number and date.

A claim is made for quantity within one week and for quality within two weeks, counted from the day the container reaches the buyer's warehouse; the buyer's report is checked against the retained sample; a claim that holds is settled with a credit on the next order; the decision can go to a laboratory or a surveyor, and the cost is shared. How a claim runs is on claims and the retained sample.

A sample for your own tests is free; the terms are on getting a sample, and the form to request a sample asks for the sizes and grades.

Labels on sealed sample bags tie each bag to the batch it came from.

Questions buyers ask

How long should a piece last in the burn test?
On the coil the factory has declared no target. Its minutes come from timing a piece on a shisha bowl in use, until the smoking ends: a 25 mm cube lasts 100 minutes, a 28 mm cube 130. On the coil, compare pieces of one size with each other.
What happens if the container does not match the sample?
A claim is made for quantity within one week and for quality within two weeks, counted from the day the container reaches the buyer's warehouse; the buyer's report is checked against the retained sample; a claim that holds is settled with a credit on the next order; the decision can go to a laboratory or a surveyor, and the cost is shared.

Test a sample the same way

The sample form asks for the sizes and grades you want to compare and the address to send them to.

Request a sample